I-Frame which is going to be resend already has FCS field added and set
(if it was required). Adding additional FCS field calculated from data +
old FCS in resend function is incorrect. This patch fix that.
Issue has been found during PTS testing.
Change-Id: Iba211a180665c5f2fa2fa462f5d5c48e2d980a21
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Git-commit: 13cac15296afe7e42088ecfcd0f1d4b658248c46
Git-repo: git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
Signed-off-by: Kamal Negi <kamaln@codeaurora.org>
It is possible that during BT OFF operation the hcon
could be released from a tasklet context while we are
trying to send the l2cap disconnect req. Make sure
that hcon is valid before dereferencing it during
l2cap disconnect req.
CRs-fixed: 383345
Change-Id: Icb12c62560013b5ebb047c1c5d4bfe04b3a793ef
Signed-off-by: Sunny Kapdi <sunnyk@codeaurora.org>
__u16 sco_pkt_type is introduced to struct sockaddr_sco. It allows bitwise
selection of SCO/eSCO packet types. Currently those bits are:
0x0001 HV1 may be used.
0x0002 HV2 may be used.
0x0004 HV3 may be used.
0x0008 EV3 may be used.
0x0010 EV4 may be used.
0x0020 EV5 may be used.
0x0040 2-EV3 may be used.
0x0080 3-EV3 may be used.
0x0100 2-EV5 may be used.
0x0200 3-EV5 may be used.
This is similar to the Packet Type parameter in the HCI Setup Synchronous
Connection Command, except that we are not reversing the logic on the EDR bits.
This makes the use of sco_pkt_tpye forward portable for the use case of
white-listing packet types, which we expect will be the primary use case.
If sco_pkt_type is zero, or userspace uses the old struct sockaddr_sco,
then the default behavior is to allow all packet types.
Packet type selection is just a request made to the Bluetooth chipset, and
it is up to the link manager on the chipset to negiotiate and decide on the
actual packet types used. Furthermore, when a SCO/eSCO connection is eventually
made there is no way for the host stack to determine which packet type was used
(however it is possible to get the link type of SCO or eSCO).
sco_pkt_type is ignored for incoming SCO connections. It is possible
to add this in the future as a parameter to the Accept Synchronous Connection
Command, however its a little trickier because the kernel does not
currently preserve sockaddr_sco data between userspace calls to accept().
The most common use for sco_pkt_type will be to white-list only SCO packets,
which can be done with the hci.h constant SCO_ESCO_MASK.
This patch is motivated by broken Bluetooth carkits such as the Motorolo
HF850 (it claims to support eSCO, but will actually reject eSCO connections
after 5 seconds) and the 2007/2008 Infiniti G35/37 (fails to route audio
if a 2-EV5 packet type is negiotiated). With this patch userspace can maintain
a list of compatible packet types to workaround remote devices such as these.
Based on a patch by Marcel Holtmann.
Rebased to 2.6.39.
Change-Id: Ide1c89574fa4f6f1b9218282e1af17051eb86315
Signed-off-by: Nick Pelly <npelly@google.com>
The length check is invalid since the length varies with type of
info response.
This was introduced by the commit cb3b3152b2
Because of this, l2cap info rsp is not handled and command reject is sent.
> ACL data: handle 11 flags 0x02 dlen 16
L2CAP(s): Info rsp: type 2 result 0
Extended feature mask 0x00b8
Enhanced Retransmission mode
Streaming mode
FCS Option
Fixed Channels
< ACL data: handle 11 flags 0x00 dlen 10
L2CAP(s): Command rej: reason 0
Command not understood
Cc: stable@vger.kernel.org
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Chan-Yeol Park <chanyeol.park@samsung.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
There has been code in place to check that the L2CAP length header
matches the amount of data received, but many PDU handlers have not been
checking that the data received actually matches that expected by the
specific PDU. This patch adds passing the length header to the specific
handler functions and ensures that those functions fail cleanly in the
case of an incorrect amount of data.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The CID is fixed to L2CAP ATT channel and so there is no need to hand it
down to the handling function. Just use a constant instead.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Several sub-modules like HIDP, rfcomm, ... need to track l2cap
connections. The l2cap_conn->hcon->dev object is used as parent for sysfs
devices so the sub-modules need to be notified when the hci_conn object is
removed from sysfs.
As submodules normally use the l2cap layer, the l2cap_user objects are
registered there instead of on the underlying hci_conn object. This avoids
any direct dependency on the HCI layer and lets the l2cap core handle any
specifics.
This patch introduces l2cap_user objects which contain a "probe" and
"remove" callback. You can register them on any l2cap_conn object and if
it is active, the "probe" callback will get called. Otherwise, an error is
returned.
The l2cap_conn object will call your "remove" callback directly before it
is removed from user-space. This allows you to remove your submodules
_before_ the parent l2cap_conn and hci_conn object is removed.
At any time you can asynchronously unregister your l2cap_user object if
your submodule vanishes before the l2cap_conn object does.
There is no way around l2cap_user. If we want wire-protocols in the
kernel, we always want the hci_conn object as parent in the sysfs tree. We
cannot use a channel here since we might need multiple channels for a
single protocol.
But the problem is, we _must_ get notified when an l2cap_conn object is
removed. We cannot use reference-counting for object-removal! This is not
how it works. If a hardware is removed, we should immediately remove the
object from sysfs. Any other behavior would be inconsistent with the rest
of the system. Also note that device_del() might sleep, but it doesn't
wait for user-space or block very long. It only _unlinks_ the object from
sysfs and the whole device-tree. Everything else is handled by ref-counts!
This is exactly what the other sub-modules must do: unlink their devices
when the "remove" l2cap_user callback is called. They should not do any
cleanup or synchronous shutdowns.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
If we want to use l2cap_conn outside of l2cap_core.c, we need refcounting
for these objects. Otherwise, we cannot synchronize l2cap locks with
outside locks and end up with deadlocks.
Hence, introduce ref-counting for l2cap_conn objects. This doesn't affect
l2cap internals at all, as they use a direct synchronization.
We also keep a reference to the parent hci_conn for locking purposes as
l2cap_conn depends on this. This doesn't affect the connection itself but
only the lifetime of the (dead) object.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch removes the status parameter of the l2cap_conn_add function.
The parameter 'status' is always 0.
Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
We use _get() and _put() for device ref-counting in the kernel. However,
hci_conn_put() is _not_ used for ref-counting, hence, rename it to
hci_conn_drop() so we can later fix ref-counting and introduce
hci_conn_put().
hci_conn_hold() and hci_conn_put() are currently used to manage how long a
connection should be held alive. When the last user drops the connection,
we spawn a delayed work that performs the disconnect. Obviously, this has
nothing to do with ref-counting for the _object_ but rather for the
keep-alive of the connection.
But we really _need_ proper ref-counting for the _object_ to allow
connection-users like rfcomm-tty, HIDP or others.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Remove code which cannot execute. l2cap_conn_add for AMP_LINK
might only be invoked when receiving data in l2cap_recv_acldata.
But this case is checked in the first statement there.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Make code more readable by changing CONF_NO_FCS_RECV which is read
as "No L2CAP FCS option received" to CONF_RECV_NO_FCS which means
"Received L2CAP option NO_FCS". This flag really means that we have
received L2CAP FRAME CHECK SEQUENCE (FCS) OPTION with value "No FCS".
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
If L2CAP_FEAT_FCS is not supported we sould miss EWS option
configuration because of break. Make code more readable by
combining FCS configuration in the single block.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Before starting quering remote AMP controllers make sure
that there is local active AMP controller.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
l2cap_send_disconn_req takes 3 parameters of which conn might be
derived from chan. Make this conversion inside l2cap_send_disconn_req.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When receiving L2CAP Create Channel Request set the channel as
L2CAP_FCS_NONE. Then in "L2CAP Config req" following field will
be set: "FCS Option 0x00 (No FCS)". So by default High Speed
channels have no FCS.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When receiving Physical Link Completed event we need to create L2CAP
channel with L2CAP Create Chan Request. Current code was sending
this command only if connection was pending (which is probably
needed in channel move case). If channel is not moved but created
Create Chan should be sent for outgoing channel which is checked
with BT_CONNECT flag.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Set chan->fcs to L2CAP_FCS_NONE only for new L2CAP channels
(not moved). Other side can still request to use FCS.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
local_amp_id is already set in l2cap_connect() which is called several
lines above.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Use helper instead of test_bit. This is the only place left using
test CONF_CONNECT_PEND flag.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Since we have started to use local_amp_id for local AMP
Controller Id it makes sense to rename ctrl_id to remote_amp_id
since it represents remote AMP controller Id.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Add processing L2CAP Create Chan Request. When channel is created
save associated high speed link hs_hcon.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When deciding whether to send EFS configuration response with success,
check rather for existence of High Speed physical link hs_hcon then
ctrl_id. There might be cases when there is ctrl_id but high speed link
is not established yet.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Disconnect logical link for high speed channel hs_hchan
associated with L2CAP channel chan.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
After physical link is created logical link needs to be created.
The process starts after L2CAP channel is created and L2CAP
Configuration Response with result PENDING is received.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When logical link creation is completed we need to save hs_hchan
which represents logical link instead of hs_hcon representing
physical link. hs_hcon shall be saved when receiving physical link
complete event.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
There is helper function used to send EFS Configuration Response.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Assignment is not needed here since err is always gets value.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Channel moves are triggered by changes to the BT_CHANNEL_POLICY
sockopt when an ERTM or streaming-mode channel is connected.
Moves are only started if enable_hs is true.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Do not retransmit previously-sent data when a "receiver ready" s-frame
with the "final" flag is received during a move.
The ERTM state machines will resynchronize at the end of a channel
move, and the state machine needs to avoid state changes during a
move.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When operating over BR/EDR, ERTM accounts for the maximum over-the-air
packet size when setting the PDU size. AMP controllers do not use the
same over-the-air packets, so the PDU size should only be based on the
HCI MTU of the AMP controller.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The L2CAP spec recommends specific retransmit and monitor timeouts for
ERTM channels that are on AMP controllers. These timeouts are
calculated from the AMP controller's best effort flush timeout.
BR/EDR controllers use the default retransmit and monitor timeouts.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Outgoing ERTM data is queued during a channel move. The ERTM state
machine is partially reset at the start of a move, and must be
resynchronized with the remote state machine at the end of the move.
Data is not sent so that there are no state transitions between the
partial reset and the resync.
Streaming mode frames are dropped during a move.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
AMP controllers expect to transmit only "complete" ACL frames. These
frames have both the "start" and "cont" bits set. AMP does not allow
fragmented ACLs.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Several different actions may be taken when an AMP physical link
becomes available. A channel being created on an AMP controller must
continue the connection process. A channel being moved needs to
either send a move request or a move response. A failed physical link
will revert to using a BR/EDR controller if possible.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The move confirm response concludes the channel move command sequence.
Receipt of this command indicates that data may begin to flow again.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The logical link confirm callback is executed when the AMP controller
completes its logical link setup. During a channel move, a newly
formed logical link allows a move responder to send a move channel
response. A move initiator will send a move channel confirm. A
failed logical link will end the channel move and send an appropriate
response or confirm command indicating a failure.
If the channel is being created on an AMP controller, L2CAP
configuration is completed after the logical link is set up.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The move response command includes a result code indicating
"pending", "success", or "failure" status. A pending result is
received when the remote address is still setting up a physical link,
and will be followed by success or failure. On success, logical link
setup will proceed. On failure, the move is stopped. The receiver of
a move channel response must always follow up by sending a move
channel confirm command.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Seung-Woo Kim